Instability phenomena of lean hydrogen/oxygen/inert-gas premixed flames on a flat burner

Katsumi, Toshiyuki; Thwe Thwe, A.; Kadowaki, Satoshi

Journal of Visualization, 25(5), p.1075 - 1083, 2022/10

https://doi.org/10.1007/s12650-022-00844-9

Lean combustion and inert-gas addition are useful to control the burning velocity of hydrogen premixed flames, and it is well known that the cellular structure forms on the front of lean hydrogen flames owing to intrinsic instability. However, the influences of inert-gas addition on the instability phenomena of lean hydrogen premixed flames are not understood fully, and then it is needed to be investigated the flame instability experimentally. In the experiments, the cellular structure and fluctuation of H/O/inert gases (Ar, N,CO) premixed flames on a flat burner were obtained using direct observation, laser diagnostics and light emission intensity to elucidate the characteristics of instability phenomena. As the results, the correlation of inert-gas addition, equivalence ratio and total flow rate with the characteristics of cellular flames was revealed, and the influences of these parameters on flame instability were discussed.

Estimation of hydrogen gas production at transient criticality in uranyl nitrate solution

Yoshida, Ryoichiro; Yamane, Yuichi; Abe, Hitoshi

Proceedings of International Nuclear Fuel Cycle Conference / Light Water Reactor Fuel Performance Conference (Global/Top Fuel 2019) (USB Flash Drive), p.408 - 414, 2019/09

In a criticality accident, it is known that some kinds of radiolysis gases are generated mainly due to kinetic energy of fission fragments. Hydrogen gas (H) is one of them, which is able to initiate explosion. The rate of H generation and its total amount can be estimated from the number of fission per second if its G value is known. In this study, it was tried to estimate G value of hydrogen gas (G(H)) by using the H concentration measured as time-series data in Transient Experiment Critical Facility (TRACY) which was carried out by Japan Atomic Energy Agency. There was time lag in the measured H concentration from its generation. To overcome those problems, measured profile of H concentration was reproduced based on a hypothetical model and its total amount was evaluated. Based on the model, the obtained G(H) was 1.2.

Conceptual design of the iodine-sulfur process flowsheet with more than 50% thermal efficiency for hydrogen production

Kasahara, Seiji; Imai, Yoshiyuki; Suzuki, Koichi*; Iwatsuki, Jin; Terada, Atsuhiko; Yan, X.

Nuclear Engineering and Design, 329, p.213 - 222, 2018/04

https://doi.org/10.1016/j.nucengdes.2017.11.046

A conceptual design of a practical large scale plant of the thermochemical water splitting iodine-sulfur (IS) process flowsheet was carried out as a heat application of JAEA's commercial high temperature gas cooled reactor GTHTR300C plant design. Innovative techniques proposed by JAEA were applied for improvement of hydrogen production thermal efficiency; depressurized flash concentration HSO using waste heat from Bunsen reaction, prevention of HSO vaporization from a distillation column by introduction of HSO solution from a flash bottom, and I condensation heat recovery in an HI distillation column. Hydrogen of about 31,900 Nm/h would be produced by 170 MW heat from the GTHTR300C. A thermal efficiency of 50.2% would be achievable with incorporation of the innovative techniques and high performance HI concentration and decomposition components and heat exchangers expected in future R&D.

R&D status in thermochemical water-splitting hydrogen production iodine-sulfur process at JAEA

Noguchi, Hiroki; Takegami, Hiroaki; Kasahara, Seiji; Tanaka, Nobuyuki; Kamiji, Yu; Iwatsuki, Jin; Aita, Hideki; Kubo, Shinji

Energy Procedia, 131, p.113 - 118, 2017/12

https://doi.org/10.1016/j.egypro.2017.09.459

The IS process is the most deeply investigated thermochemical water-splitting hydrogen production cycle. It is in a process engineering stage in JAEA to use industrial materials for components. Important engineering tasks are verification of integrity of the total process and stability of hydrogen production in harsh environment. A test facility using corrosion-resistant materials was constructed. The hydrogen production ability was 100 L/h. Operation tests of each section were conducted to confirm basic functions of reactors and separators, etc. Then, a trial operation for integration of the sections was successfully conducted to produce hydrogen of about 10 L/h for 8 hours.

IS process hydrogen production test for components and system made of industrial structural material, 1; Bunsen and HI concentration section

Tanaka, Nobuyuki; Takegami, Hiroaki; Noguchi, Hiroki; Kamiji, Yu; Iwatsuki, Jin; Aita, Hideki; Kasahara, Seiji; Kubo, Shinji

Proceedings of 8th International Topical Meeting on High Temperature Reactor Technology (HTR 2016) (CD-ROM), p.1022 - 1028, 2016/11

Japan Atomic Energy Agency (JAEA) has manufactured 100 NL/h-H-scale hydrogen test apparatus. In advance to conduct the continuous operation, we investigated performance of the components in each section of the IS process. In this paper, the results of test of Bunsen and HI concentration sections was shown. In Bunsen reaction, section, we confirmed that outlet gas flow rate included no SO gas, indicating that all the feed SO gas was absorbed to the solution in the Bunsen reactor for the Bunsen reaction. On the basis of these results, we evaluated that Bunsen reactor was workable. In HI concentration section, HI concentration was conducted by EED stack. As a result, it can concentrate HI in HIx solution as theoretically predicted on the basis of the previous paper. Based on the results added to that shown in Series II, we have conducted a trial continuous operation and succeeded it for 8 hours.

Numerical analysis on deflagration-to-detonation transition of a hydrogen-oxygen mixture in a smooth tube

Inaba, Yoshitomo; Kotchourko, A.*; Breitung, W.*

JAERI-Tech 2005-053, 24 Pages, 2005/09

JAERI-Tech-2005-053.pdf:4.3MB

The Flow and Combustion Engineering Division at the Forschungszentrum Karlsruhe carried out the explosion experiments of hydrogen-oxygen mixtures in a smooth tube made of stainless steel after two radiolysis gas explosion accidents occurred in Japanese and German BWRs. In these experiments, stoichiometric hydrogen-oxygen mixtures with different initial pressures were used. The pressure in the tube and the strain of the tube were measured, and then the structural response during the detonation and the Deflagration-to-Detonation Transition (DDT) process were investigated. In the present study, a numerical analysis was performed to simulate one of the experiments by the use of the 3-dimensional turbulent combustion analysis code COM3D, which has been developed in FZK, and a DDT process was calculated. The COM3D code contains a reaction rate constant, which must be obtained empirically from experimental results. In the present calculation, the reaction rate constant was assumed to be an exponential function. As a result, it was found that the COM3D code can simulate the DDT process.

Tritium recovery from solid breeder blanket by water vapor addition to helium sweep gas

Kawamura, Yoshinori; Iwai, Yasunori; Nakamura, Hirofumi; Hayashi, Takumi; Yamanishi, Toshihiko; Nishi, Masataka

Fusion Science and Technology, 48(1), p.654 - 657, 2005/07

https://doi.org/10.13182/FST05-A1010

Adding some amount of hydrogen to the helium sweep gas is effective for tritium extraction from blanket, but it causes permeation of tritium to a cooling system. In the design study of a demonstration reactor in JAERI, tritium leakage has been estimated to be about 20% of bred tritium under typical sweep gas conditions. If these tritiums are recovered under the ITER-WDS condition, tritium leakage limitation has to be less than 0.3% of typical case. Water vapor addition to the sweep gas is effective not only for blanket tritium extraction but also for permeation prevention. The reaction rate of isotope exchange is larger than the case of H, and the equilibrium constant is also expected to be about 1.0. When the H/T ratio is 100, tritium inventory of breeder material is larger than the case of H addition. However it is not so large. In case of HO sweep, separation of tritiated water from helium seems to be easyer, but the process that changes HTO to HT is necessary.

Verification of HTTR hydrogen production system analysis code using experimental data of mock-up model test facility with a full-scale reaction tube; Cooling system of the secondary helium gas using steam generator and radiator (Contract research)

Sato, Hiroyuki; Ohashi, Hirofumi; Inaba, Yoshitomo; Maeda, Yukimasa; Takeda, Tetsuaki; Nishihara, Tetsuo; Inagaki, Yoshiyuki

JAERI-Tech 2005-014, 89 Pages, 2005/03

JAERI-Tech-2005-014.pdf:7.25MB

In a hydrogen production system using HTTR, it is required to control a secondary helium gas temperature within an allowable value at an intermediate heat exchanger (IHX) inlet to prevent a reactor scram. To mitigate thermal disturbance of the secondary helium gas caused by the hydrogen production system, a cooling system of the secondary helium gas using a steam generator(SG) and a radiator will be installed at the downstream of the chemical reactor. In order to verify a numerical analysis code of the cooling system, numerical analysis has been conducted. The pressure controllability in SG is highly affected by the heat transfer characteristics of air which flows outside of the heat exchanger tube of the radiator. In order to verify a numerical analysis code of the cooling system, the heat transfer characteristics of air has been investigated with experimental results of a mock-up model test. It was confirmed that numerical analysis results were agreed well with experimental results, and the analysis code was successfully verified.

Evaluation of hydrogen permeation of fuel cladding materials under low energy plasma

Ogawa, Hiroaki*; Kiuchi, Kiyoshi

JAERI-Research 2002-037, 48 Pages, 2002/12

JAERI-Research-2002-037.pdf:2.57MB

The difference in hydrogen permeation among candidate cladding materials such as 25Cr-35Ni stainless steel, Nb liner and reference materials such as 18Cr-8Ni SS, and Zr of Zircaloy base metal were evaluated by low energy plasma permeation simulated to hydrogen excited by heavy neutron irradiation. RF excitation source was arranged for the experimental apparatus in cooperating with temperature and bias control. Comparing with the thermodynamic gas driven permeation (GDP) in the same hydrogen pressure, the hydrogen permeation rate by the plasma driven permeation (PDP) was markedly accelerated at low to medium temperature range. The temperature dependency showed a knick at around 530K due to hydrogen-defect interactions. Comparing with Zr, Nb showed the high hydrogen solubility without the degradation by hydrate formation that is required to a getter material. The difference in PDP among candidates was analyzed with a new dissolution model for hydrogen.

Research and development of HTTR hydrogen production systems

Shiozawa, Shusaku; Ogawa, Masuro; Inagaki, Yoshiyuki; Onuki, Kaoru; Takeda, Tetsuaki; Nishihara, Tetsuo; Hayashi, Koji; Kubo, Shinji; Inaba, Yoshitomo; Ohashi, Hirofumi

Proceedings of 17th KAIF/KNS Annual Conference, p.557 - 567, 2002/04

The research and development program on nuclear production of hydrogen was started on January in 1997 as a study consigned by Ministry of Education, Culture, Sports, Science and Technology. A hydrogen production system connected to the HTTR is being designed to be able to produce hydrogen of about 4000 m3/h by steam reforming of natural gas, using a nuclear heat of 10 MW supplied by the HTTR. In order to confirm controllability, safety and performance of key components in the HTTR hydrogen production system, the facility for an out-of-pile test was constructed on the scale of approximately 1/30 of the HTTR hydrogen production system. Essential tests are also carried out to obtain detailed data for safety review and development of analytical codes. Other basic studies on the hydrogen production technology of thermochemical water splitting called an iodine sulfur (IS) process, has been carried out for more effective and various uses of nuclear heat. This paper describes the present status and a future plan on the R&D of the HTTR hydrogen production systems in JAERI.